Plain guides to the DOT annual inspection. Call when you are parked, never while driving.(305) 699-5857
Get a life quote

Tools

Brake readjustment limits, by chamber type

Look up the pushrod stroke limit for clamp, DD-3, bolt and rotochamber brake chambers. The full tables are below the lookup.

A mechanic presses a tread depth gauge into a truck steer tire
Short answer

The maximum pushrod stroke must not be greater than the values in the Appendix A tables, and any brake stroke over the readjustment limit is rejected.1 A Type 30 clamp chamber, for example, has a limit of 2 inches (50.8 mm) as a standard stroke chamber and 2 1/2 inches (63.5 mm) as a long stroke chamber.1 Take the reading with the engine shut off, the reservoir held at 80 to 90 psi and the brakes pushed fully on.1

Prices checked
No prices on this page
Rule checked
November 20, 2026, Appendix A to Part 396, section 1.a(5)
Applies to
Air brake chambers on trucks, tractors and trailers in the annual inspection
On this page
  1. 01Look up a limit
  2. 02How the stroke is measured
  3. 03Clamp type chambers
  4. 04DD-3, bolt type and rotochamber
  5. 05Standard stroke or long stroke
  6. 06Chambers that are not in the tables
  7. 07If a brake is over the limit
  8. 08Questions people ask

Look up a limit

The form starts with a Type 30 clamp chamber and an example reading. Change any box and the limit updates.

Brake readjustment limit Live

Your brake chamber

Readjustment limit 2 in. (50.8 mm)
Chamber
Clamp chamber, type 30, standard stroke
Outside diameter
8 3/32 in. (206 mm)
Your measured stroke
Within the limit, 0.25 in. (6.4 mm) to spare

A lookup of the Appendix A tables, not an inspection. You can type 1.75 or 1 3/4, and a number ending in mm works too. The stroke is within the limit when it is not greater than the table value. The 1 3/4 inch reading is an example. The rule sets the test conditions in the steps below.

Get a life quote

How the stroke is measured

  1. Set the air. Shut the engine off and hold the reservoir between 80 and 90 psi.1
  2. Apply the brakes fully. Appendix A says the stroke is read while the brakes are fully on.1
  3. Know the chamber. Read the type off the chamber and find the table for its family below. The CVSA bulletin says the size type comes from the outside diameter, measured with a caliper or a chamber measuring tool.2
  4. Compare. The stroke must not be greater than the table value.1
A shop inspector with a clipboard talks with a truck driver beside his tractor

Life insurance for drivers

Licensed agents compare several insurance companies and call you back with prices. You decide.

Get a life quoteOr call (305) 699-5857

Clamp type chambers

TypeOutside diameterStandard stroke limitLong stroke limitLong stroke, 3 inch rated
64 1/2 in. (114 mm)1 1/4 in. (31.8 mm)Not listedNot listed
95 1/4 in. (133 mm)1 3/8 in. (34.9 mm)Not listedNot listed
125 11/16 in. (145 mm)1 3/8 in. (34.9 mm)1 3/4 in. (44.5 mm)Not listed
166 3/8 in. (162 mm)1 3/4 in. (44.5 mm)2 in. (50.8 mm)Not listed
206 25/32 in. (172 mm)1 3/4 in. (44.5 mm)2 in. (50.8 mm)2 1/2 in. (63.5 mm)
247 7/32 in. (184 mm)1 3/4 in. (44.5 mm)2 in. (50.8 mm)2 1/2 in. (63.5 mm)
308 3/32 in. (206 mm)2 in. (50.8 mm)2 1/2 in. (63.5 mm)Not listed
369 in. (229 mm)2 1/2 in. (63.5 mm)Not listedNot listed

Checked November 20, 2026. Source 1. The last column is the footnoted value for Type 20 and Type 24 chambers with a 3 inch (76 mm) rated stroke.

DD-3, bolt type and rotochamber

Bendix DD-3

TypeOutside diameterReadjustment limit
308 1/8 in. (206 mm)2 1/4 in. (57.2 mm)

Bolt type

TypeOutside diameterReadjustment limit
A6 15/16 in. (176 mm)1 3/8 in. (34.9 mm)
B9 3/16 in. (234 mm)1 3/4 in. (44.5 mm)
C8 1/16 in. (205 mm)1 3/4 in. (44.5 mm)
D5 1/4 in. (133 mm)1 1/4 in. (31.8 mm)
E6 3/16 in. (157 mm)1 3/8 in. (34.9 mm)
F11 in. (279 mm)2 1/4 in. (57.2 mm)
G9 7/8 in. (251 mm)2 in. (50.8 mm)

Rotochamber

TypeOutside diameterReadjustment limit
94 9/32 in. (109 mm)1 1/2 in. (38.1 mm)
124 13/16 in. (122 mm)1 1/2 in. (38.1 mm)
165 13/32 in. (138 mm)2 in. (50.8 mm)
205 15/16 in. (151 mm)2 in. (50.8 mm)
246 13/32 in. (163 mm)2 in. (50.8 mm)
307 1/16 in. (180 mm)2 1/4 in. (57.2 mm)
367 5/8 in. (194 mm)2 3/4 in. (69.9 mm)
508 7/8 in. (226 mm)3 in. (76.2 mm)

Checked November 20, 2026. Source 1, the Bendix DD-3, bolt type and rotochamber tables.

Standard stroke or long stroke

Only clamp type chambers have a separate long stroke column. The CVSA bulletin says all stroke markings a maker puts on a chamber give the rated stroke, not the adjustment limit, and that rated stroke is generally one half inch (13 mm) more than the limit.2 It lists three ways a long stroke chamber is identified, service instructions embossed or stamped on it, a trapezoid tag showing the rated stroke, or square air ports or a square embossment, and says compliant long stroke chambers use at least two of the three.2 If you cannot find a long stroke mark, use the standard stroke limit. It is the lower number.

Chambers that are not in the tables

For actuator types not listed, the pushrod stroke must not be greater than 80 percent of the rated stroke marked on the actuator, or greater than the readjustment limit the maker marked on it.1

If a brake is over the limit

A brake found out of adjustment is a failing item, and a brake over the limit is rejected.1 Appendix A also says an automatic brake adjuster that is out of adjustment on first inspection must be evaluated to find out why it is not working. The cause has to be corrected, and it is not acceptable to adjust an automatic adjuster by hand without first correcting that problem.1 Do not run a vehicle with a brake over its limit. See the failing items page and the inspection checklist. The home page is DOT Annual.

Questions people ask

What is the readjustment limit for a Type 30 chamber?

For a clamp type chamber it is 2 inches (50.8 mm) standard stroke and 2 1/2 inches (63.5 mm) long stroke. A Bendix DD-3 Type 30 is 2 1/4 inches (57.2 mm), and a Type 30 rotochamber is 2 1/4 inches (57.2 mm).1

Is the number marked on the chamber the limit?

No. The CVSA bulletin says the markings show the rated stroke, which is generally one half inch more than the adjustment limit.2

At what pressure is stroke measured?

Appendix A says 80 to 90 psi in the reservoir, engine off, with the brakes fully applied.1

Sources (2)
  1. Cornell Law School Legal Information Institute, Appendix A to Part 396 Minimum Periodic Inspection Standards, opened November 20, 2026. law.cornell.edu
  2. Commercial Vehicle Safety Alliance, Inspection Bulletin 2014-02 Identification of Long Stroke Brake Chambers or Brake Adjustment Limit Markings, created April 10, 2014, opened November 20, 2026. cvsa.org

Life insurance for drivers

The brakes are in spec. Is your family covered?

The truck gets inspected every year. Your family’s plan deserves the same check. A licensed agent compares life insurance from several insurance companies and calls you back with prices. You decide if and when to apply.

Get a life quoteOr call (305) 699-5857

DOT Annual is run by an independent, licensed insurance agency. We are not FMCSA, CVSA, a state agency, an inspection shop, a medical examiner or a motor carrier.

A driver checks trailer lights and tires on a morning walkaround at the truck yard
CallGet a life quote